Clean windshield wipers with mild soap or glass cleaner, a soft cloth, and gentle pressure so you remove road film without damaging the rubber. Done right, this reduces streaks, squeaks, and helps your blades last longer.

Quick Scoop

  • Time needed: About 5–10 minutes per car.
  • How often: Roughly once a month, and after long dirty/wet drives or pollen season.
  • Basic idea: Clean the glass, lift the arms, wipe along the rubber edge until the cloth comes away clean, then let everything dry.

What you’ll need

  • Bucket of warm, mildly soapy water or windshield washer fluid.
  • Alternatively: water + a little vinegar, or a dedicated glass cleaner.
  • Soft microfiber cloths or paper towels.
  • Optional: small soft brush (old toothbrush) for pivots and hinges.
  • Optional: a bit of silicone spray or petroleum jelly for older, dried rubber (very small amount, wiped off after).

Avoid harsh solvents, gasoline, WD‑40, or abrasive pads on the rubber or glass; they can smear, dry, or damage the blade and windshield.

Step‑by‑step: how to clean windshield wipers

  1. Wash the windshield first
    • Rinse and wash the glass with car shampoo or glass cleaner to remove grit that could get dragged under the blade.
 * Rinse thoroughly so there’s no soapy film left.
  1. Lift the wiper arms safely
    • Gently pull each arm away from the windshield until it locks upright (if your car supports that position).
 * If they don’t lock, support the arm with one hand so it doesn’t snap back onto the glass.
  1. Clean the rubber blade edge
    • Soak a folded microfiber cloth in warm, soapy water or glass cleaner and wring it out slightly.
 * Pinch the blade near the base with the cloth and slide from base to tip in one smooth pass.
 * Re‑fold or switch to a clean part of the cloth and repeat passes until there’s no more black/gray dirt coming off.

 * For stubborn buildup, lightly scrub the sides of the rubber with the damp cloth or a soft brush, not your fingernails.
  1. Clean the wiper arm and joints
    • Wipe down the metal or plastic arm, especially the hinge and pivot points where dust and road salt collect.
 * Remove any leaves, sand, or ice residue at the base of the windshield so it doesn’t get dragged back onto the blade.
  1. Optional: vinegar or “deep clean” pass
    • For older blades or heavy film, mix water with a little white vinegar on a cloth and repeat the blade wipe.
 * Immediately follow with a pass of plain water on a clean cloth to remove vinegar residue so it doesn’t sit on the rubber or paint.
  1. Rinse and dry
    • Lightly wipe the blade and arm with a damp cloth (plain water) to remove leftover cleaner, then dry with a dry microfiber.
 * Gently lower the arms back to the glass; don’t let them snap down.
  1. Test the wipers
    • Spray washer fluid and run the wipers for a few swipes.
    • Check for:
      • Fewer streaks
      • Less squeaking
      • Good, even contact across the whole sweep

Extra tips, what to avoid, and when to replace

What to avoid

  • Don’t use WD‑40 on the rubber: it’s a water displacer, can smear on the glass, and may degrade the blade over time.
  • Don’t use strong solvents (like paint thinners or harsh spirits) on blades or windshields.
  • Don’t scrub rubber with abrasive pads or sharp edges; that can tear the wiping lip and worsen streaks.

When cleaning isn’t enough

Even perfectly cleaned blades need replacing periodically:

  • If the rubber is cracked, torn, or chunked out anywhere.
  • If the blade misses areas in the middle or chatters constantly even after cleaning and glass prep.
  • If you see lines where the rubber has hardened and won’t flex to the glass.

Most guides suggest replacing wiper blades about every 6–12 months depending on climate, sun exposure, and use.

Forum‑style tricks & “latest” chatter

Car forums and tip communities share a few recurring ideas about how to clean windshield wipers:

  • Many drivers just use regular glass cleaner on a microfiber cloth and wipe the blades top‑to‑bottom; it’s quick and works well for light buildup.
  • Detailers often recommend pairing blade cleaning with a full windshield decontamination (clay bar and proper glass cleaner) for the best streak‑free results.
  • Some people lightly condition old rubber with a touch of silicone or petroleum jelly after cleaning, then wipe the excess off, mainly for cars that sit in the sun.

If you want a very short workflow to remember “how to clean windshield wipers,” think:

Clean glass → lift arms → wipe rubber until cloth is clean → wipe arms/pivots → rinse and dry → test with washer fluid.

TL;DR: To clean windshield wipers, wash the windshield, lift the arms, wipe the rubber edge several times with a cloth soaked in warm soapy water or glass cleaner until no dirt comes off, clean the arms and pivots, then rinse, dry, and test; if streaks persist or the rubber is cracked, it’s time to replace the blades.